The Basics of Plumbing Skills for Bathtub Installation

Appointment

Presented here in the next paragraph yow will discover lots of excellent resources regarding How to Install a Bathtub.


Tools You Need to Install a New Bathtub
Mounting a tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard task. If the old tub is readily accessible, the task can move quickly; if you need to open a wall surface to remove the old bathtub and place the new bathtub, the job is a lot harder. In either instance, the job is within a residence handyman's abilities, although you will need a helper to leave the old bathtub as well as embeded in the new one. See to it you have certified yourself for the job and also are comfortable trying it. As opposed to working with a contractor to take over a halfway-completed project, it is far better to take into consideration employing one before you start. Possibilities are you might require a professional plumber to make tube links.
This short article will aid you mount a brand-new tub in your restroom if you have actually currently acquired a brand-new bathtub and also do not require to alter the setup of your previous supply of water pipelines.
Your devices as well as product checklist ought to consist of the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Removing Old Taps


    If you require to replace old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the water supply. After doing so, activate the taps to drain pipes any type of water remaining in the system. The process of eliminating the existing taps can be rather troublesome due to the limited gain access to that is frequently the instance.
    Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
    Prior to moving on to fit the new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a connection to the existent supply pipelines.
    If you require to fit a monobloc, after that you will certainly require decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
    Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer given backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The former type should be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Setting up the Tub


    Utilizing the two wooden boards under its feet, position the bath tub in the needed setting. The wooden boards are handy in uniformly spreading the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little factors.
    The next objective is to make sure that the bath tub is leveled all round. This can be attained by checking the level and also changing the feet on the bathtub till the spirit level reads level.
    To install faucets, fit the bottom of the outermost adaptable faucet adapter to the proper supply pipeline by making a compression join; then do the same for the various other faucet.
    Switch on the water as well as inspect all joints and also brand-new pipework for leaks and tighten them if required. Fill up the bath tub as well as additionally inspect the overflow outlet as well as the regular electrical outlet for leaks.
    Lastly, repair the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the bath tub needs to wait until the bath tub has actually been utilized at the very least once as this will certainly settle it into its last setting.

    Planning for the Installment


    First of all, the supporting frame provided with the bathroom needs to be fitted (if required) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the faucets device to stop stress on the bath tub.
    Fit the flexible faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
    Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to currently be ready to be suited its final setting.

    Tiling Around the Bath tub


    In the location where the bath satisfies the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to fracture a rigid seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, bring about complications with dampness and also feasible leaks to the ceiling below.
    You can select from a variety of coloured sealants to blend in your fixtures and also installations. They are sold in tubes and cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of drenched paper or soft rope. Remember to always load the bathtub with water before sealing, to permit the movement experienced when the tub is in use. The sealant can crack fairly very early if you do not think about this activity prior to securing.
    Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently offered on the market. It is recommended to fit the ceramic tiles making use of waterproof or waterproof sticky and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    A Step-by-Step Guide to Installing a Bathtub

    I discovered that content on Installing A Bathtub while doing a lookup on the search engines. Be sure to take the opportunity to promote this post if you enjoyed it. Many thanks for your time spent reading it.


    Top Article

    Leave a Reply

    Your email address will not be published. Required fields are marked *